Seeed Studio XIAO Expansion board

A powerful functional expansion board for Seeed Studio XIAO of only half Raspberry Pi 4 size. It enables build prototype and project in easy and quick way. With its rich peripherals including OLED, RTC, expandable memory, passive buzzer, RESET/User button, 5V servo connector, multiple data interfaces… you could explore infinite possibilities of Seeed Studio XIAO . Circuit python is also well supported by this board.

As Seeed Studio XIAO form factor, all Seeed Studio XIAO boards support both Grove Shield for Seeed Studio XIAO and Seeed Studio Expansion Base for XIAO. There is a slight difference between the pins and refer to the Pinout it is easy to manage.

Seeed Studio XIAO SAMD21 , Seeed Studio XIAO RP2040, and Seeed Studio XIAO nRF52840 are compatible to the Seeed Studio Expansion Base for XIAO.

Get One Now 🖱️

Features

Quick Prototyping: Easy debug and Reset with RESET button and SWD pin led out to male header. 0.96”OLED, enables visual data display without PC serial monitor; Convenient plug and play Grove connectors support multiple data protocols, including IIC, Uart, Analog/Digital; No soldering needed with all pin led out.
Rich peripherals: OLED display, RTC, expandable memory space, passive buzzer, user button, on board battery management chip.
No Soldering Needed: All pin led out. Convenient plug and play Grove connectors support multiple data protocols, including IIC, Uart, Analog/Digital.
Circuit Python Supported: Well supports circuit python. MicroSD card slot enables memory space expand, making it possible to allocate more libraries needed in prototyping and project building.
Mini Size: Compact and elegant with only half Raspberry Pi 4 size, especially suitable for projects require mini size.

Specification

Item	Value
Operating voltage	5V / 3.7V Lithium Battery
Charging current	460mA (Max)
RTC timer precision	± 1.5S/DAY(25°C)
RTC battery	CR1220
Display	0.96" OLED display
Expandable memory	MicroSD card
Grove Interface	Grove IIC2, Grove UART1, A0/D0 Grove*1
Other External Equipment	Passive buzzer, user button, 5V servo connector

Applications

SWD debug
Rapid prototyping
Data display
Mini Size Project

Part List

Item	Value
Seeed Studio Expansion Base for XIAO	*1

note

This product does not include Seeed Studio XIAO and battery, please click this link to get Seeed Studio XIAO SAMD21

Getting Started

Materials Required

Seeed Studio XIAO SAMD21 (Pre-solder)	Seeed Studio Expansion Base for XIAO

Get ONE Now	Get ONE Now

Hardware Overview

There are an external MicroSD card slot and RTC Battery Holder, the MicroSD card mostly is used for saving and run the python.py file, the RTC is for tracks the current time and can be used to program actions at a specific time.

Pinout Diagram

External headers-pin description for Grove-Shield for Seeed Studio XIAO .

Expansion Board Usage

Connection

Put the Seeed Studio XIAO SAMD21 on the expansion board, the Seeed Studio XIAO SAMD21 green LED should light up.

note

Please plug the Seeed Studio XIAO on the expansion board first, then plug Type-C, Remember pluing Seeed Studio XIAO into the middle of the two female header connectors, otherwise you will damage the Seeed Studio XIAO and the expansion board.

Battery usage

The Seeed Studio Expansion Base for XIAO can be powered by a battery, so if you do some demo that needs to be moved, that battery will help you to solve the power supply issue. when you plug the battery please watch out for the positive and negative anodes, follow the picture to connect the battery in case of damage the board.

In addition, the board charged the battery when you plug the battery cable and the type-C cable and switch the button to on.

As the below picture, if the LED flashing which means the battery does not charge or the board does not connect battery if the LED keeps light on which is mean the battery is charging.

Modules on the expansion board

Rich peripherals on board including:

OLED display: Visual data display without connecting to PC, which enables debug in a more efficient way, and builds application such as a sensor hub, data monitor system, etc.
RESET button: No more jumper wire and short circuit, easy reset with just one click.
SWD debug: SWD pin led out as male pin header, making debugger connection and firmware download much easier.
High precision RTC: High precision real-time clock with battery backup, enable maintain accurate time when the main power is turned off.
Expandable memory: With a MicroSD card slot on the back, no worry on memory limit any more when adding libraries and using circuit python.
User button: Besides the RESET button, also provide with another user-defined button.
Passive buzzer: Same passive buzzer on Wio Terminal, with which you could change the PMW frequency to award different beep sound to get a "buzzer music".
Grove connectors: All pin led out, plug and play grove connectors support common data protocols (Grove IIC2, Grove UART1, A0/D0 Grove*1)
Lipo Battery Charging: JST2.0mm standard lipo battery connector and battery management system, supports both USB and lipo battery power supply, and easy onboard battery recharge.
5V servo connector: 5V output led out to male header for 5V servo and sensor connection.

OLED Display

This example introduces how to use the OLED display on the Seeed Studio Expansion Base for XIAO.

Step 1. Install the Seeed Studio XIAO SAMD21 on the Expansion board then conect the Type-C cable.

Step 2. Install the u8g2 library, this is the guide how to install the library.

Step 3. Copy the code and stick on the Ardiono IDE then upload it.

OLED Code

#include <Arduino.h>
#include <U8x8lib.h>
#include <Wire.h>

U8X8_SSD1306_128X64_NONAME_HW_I2C u8x8(/* clock=*/ PIN_WIRE_SCL, /* data=*/ PIN_WIRE_SDA, /* reset=*/ U8X8_PIN_NONE);   // OLEDs without Reset of the Display

void setup(void) {
  u8x8.begin();
  u8x8.setFlipMode(1);   // set number from 1 to 3, the screen word will rotary 180
}

void loop(void) {
  u8x8.setFont(u8x8_font_chroma48medium8_r);
  u8x8.setCursor(0, 0);
  u8x8.print("Hello World!");
}

LED control by User Button

This example introduces how to use the button on the Seeed Studio Expansion Base for XIAO to control the LED on the Seeed Studio XIAO SAMD21.

Step 1. Install the Seeed Studio XIAO SAMD21 on the Expansion board then conect the Type-C cable.

Step 2. Open Arduino IDE, Copy the code and stick on the Ardiono IDE then upload it.

Code

const int buttonPin = 1;     // the number of the pushbutton pin
int buttonState = 0;         // variable for reading the pushbutton status

void setup() {
  // initialize the LED pin as an output:
  pinMode(LED_BUILTIN, OUTPUT);
  // initialize the pushbutton pin as an input:
  pinMode(buttonPin, INPUT_PULLUP);

}

void loop() {
  // read the state of the pushbutton value:
  buttonState = digitalRead(buttonPin);

  // check if the pushbutton is pressed. If it is, the buttonState is HIGH:
  if (buttonState == HIGH) {
    // turn LED on:
    digitalWrite(LED_BUILTIN, HIGH);
  } else {
    // turn LED off:
    digitalWrite(LED_BUILTIN, LOW);
  }

}

Buzzer

The Buzzer is default connected to the Pin A3, if you want to remove the buzzer function, just follow the below picture, cut off the line.

Play Song with Passive Buzzer

This example uses Buzzer on the Seeed Studio Expansion Base for XIAO to play Happy birthday.

Step 1. Install the Seeed Studio XIAO SAMD21 on the Expansion board then conect the Type-C cable.

Step 2. Open Arduino IDE, Copy the code and stick on the Ardiono IDE then upload it.

Code

int speakerPin = A3;
int length = 28; // the number of notes
char notes[] = "GGAGcB GGAGdc GGxecBA yyecdc";
int beats[] = { 2, 2, 8, 8, 8, 16, 1, 2, 2, 8, 8, 8, 16, 1, 2, 2, 8, 8, 8, 8, 16, 1, 2, 2, 8, 8, 8, 16 };
int tempo = 150;
void playTone(int tone, int duration) {
  for (long i = 0; i < duration * 1000L; i += tone * 2) {
    digitalWrite(speakerPin, HIGH);
    delayMicroseconds(tone);
    digitalWrite(speakerPin, LOW);
    delayMicroseconds(tone);
  }
}

void playNote(char note, int duration) {
  char names[] = {'C', 'D', 'E', 'F', 'G', 'A', 'B',
                  'c', 'd', 'e', 'f', 'g', 'a', 'b',
                  'x', 'y'
                 };
  int tones[] = { 1915, 1700, 1519, 1432, 1275, 1136, 1014,
                  956,  834,  765,  593,  468,  346,  224,
                  655 , 715
                };
  int SPEE = 5;

  // play the tone corresponding to the note name

  for (int i = 0; i < 16; i++) {
    if (names[i] == note) {
      int newduration = duration / SPEE;
      playTone(tones[i], newduration);
    }
  }
}

void setup() {
  pinMode(speakerPin, OUTPUT);
}

void loop() {
  for (int i = 0; i < length; i++) {
    if (notes[i] == ' ') {
      delay(beats[i] * tempo); // rest
    } else {
      playNote(notes[i], beats[i] * tempo);
    }
    // pause between notes
    delay(tempo);
  }
}

Servo Control by Rotary Angle Sensor

This example uses a rotary angle sensor to control servo via integration ports on the Seeed Studio Expansion Base for XIAO.

Step 1. Install the Seeed Studio XIAO SAMD21 on the Expansion board then conect the Type-C cable.

Step 2. Connect the Servo cable to I2C port, rotary angle sensor to D0.

Step 3. Open Arduino IDE, Copy the code and stick on the Ardiono IDE then upload it.

#include <Servo.h>
#include <Arduino.h>
#include <Wire.h>

#define ROTARY_ANGLE_SENSOR A0
#define ADC_REF 3 //reference voltage of ADC is 3v.If the Vcc switch on the seeeduino
#define GROVE_VCC 3 //VCC of the grove interface is normally 3v
#define FULL_ANGLE 300 //full value of the rotary angle is 300 degrees

Servo myservo;  // create servo object to control a servo
// twelve servo objects can be created on most boards

int pos = 0;    // variable to store the servo position

void setup() {
  Serial.begin(9600);
  pinMode(ROTARY_ANGLE_SENSOR, INPUT);
  myservo.attach(5);  // attaches the servo on pin 9 to the servo object
}

void loop() {

  float voltage;
  int sensor_value = analogRead(ROTARY_ANGLE_SENSOR);
  voltage = (float)sensor_value * ADC_REF / 1023;
  float degrees = (voltage * FULL_ANGLE) / GROVE_VCC;
  Serial.println("The angle between the mark and the starting position:");
  Serial.println(degrees);
  delay(50);
  myservo.write(degrees);
}

RTC clock display

This example uses RTC to display the clock on the OLED.

Step 1. Install the Seeed Studio XIAO SAMD21 on the Expansion board then conect the Type-C cable.

Step 2. Install the u8g2 and PCF8563 library, this is the guide how to install the library.

Step 3. Copy the code and stick on the Ardiono IDE then upload it.

#include <Arduino.h>
#include <U8x8lib.h>
#include <PCF8563.h>
PCF8563 pcf;
#include <Wire.h>

U8X8_SSD1306_128X64_NONAME_HW_I2C u8x8(/* clock=*/ PIN_WIRE_SCL, /* data=*/ PIN_WIRE_SDA, /* reset=*/ U8X8_PIN_NONE);   // OLEDs without Reset of the Display

void setup() {
  Serial.begin(115200);
  u8x8.begin();
  u8x8.setFlipMode(1);
  Wire.begin();
  pcf.init();//initialize the clock
  pcf.stopClock();//stop the clock
  pcf.setYear(20);//set year
  pcf.setMonth(10);//set month
  pcf.setDay(23);//set dat
  pcf.setHour(17);//set hour
  pcf.setMinut(33);//set minut
  pcf.setSecond(0);//set second
  pcf.startClock();//start the clock
}

void loop() {
  Time nowTime = pcf.getTime();//get current time
  u8x8.setFont(u8x8_font_chroma48medium8_r);   // choose a suitable font

  u8x8.setCursor(0, 0);
  u8x8.print(nowTime.day);
  u8x8.print("/");
  u8x8.print(nowTime.month);
  u8x8.print("/");
  u8x8.print("20");
  u8x8.print(nowTime.year);
  u8x8.setCursor(0, 1);
  u8x8.print(nowTime.hour);
  u8x8.print(":");
  u8x8.print(nowTime.minute);
  u8x8.print(":");
  u8x8.println(nowTime.second);
  delay(1000);
}

Acrylic Case for Seeed Studio Seeed Studio Expansion Base for XIAO

We made this acrylic case for protecting the Seeed Studio Expansion Base for XIAO, those are acrylic case components.

Compare with the Grove Shield for Seeed Studio XIAO , the Seeed Studio Expansion Base for XIAO added a lot useful modules for the users.

This Acrylic case easy to build it up and it also can dress the case look neater.

Circuitpython on Seeed Studio XIAO SAMD21 with expansion board

This wiki introduce how to install and run the official CircuitPython by Adafruit Industries on the Seeed Studio XIAO SAMD21 development board !

CircuitPython is a programming language designed to simplify experimenting and learning to program on low-cost microcontroller boards. It makes getting started easier than ever with no upfront desktop downloads needed. Once you get your board set up, open any text editor, and get started editing code. For more info, please refer to here.

Installing CircuitPython

Step 1. Install the Seeed Studio XIAO SAMD21 on the Expansion board then conect the Type-C cable.

Step 2. Download the official CircuitPython Bootloader for Seeed Studio XIAO SAMD21 . A .uf2 , the flie will be store in your PC download.

Step 3. Entering the DFU bootloader mode by press the reset button twice quickly on the Seeed Studio Expansion Base for XIAO, then your PC will appear Arduino drive.

Step 4. An external drive named Arduino should appear in your PC. Drag the downloaded CircuitPython uf2 files to the Arduino drive.

Step 5. Once loaded the CircuitPython bootloader, unplug the USB Type-C and re-connect. A new external drive called CIRCUITPY should be appear.

Step 6. Now, CircuitPython is loaded on Seeed Studio XIAO SAMD21 ! All you need to do it's to write you python program and name it main.py and drag it onto the CIRCUITPY drive.

CircuitPyhton Blink example

There is a simple example introduce how to use the CirsuitPython on the Seeed Studio XIAO .

Step 1 Create a txt file name main on the CIRCUITPY drive.

note

The main name is one of these: code.txt, code.py, main.py, main.txt, there is more detail about this behavior.

Step 2 Paste the code on the main file then save it, you will see the orange LED blinking on the Seeed Studio XIAO SAMD21 board.

Code

import time
import board
from digitalio import DigitalInOut, Direction

led = DigitalInOut(board.D13)
led.direction = Direction.OUTPUT

while True:
    led.value = True
    time.sleep(1)
    led.value = False
    time.sleep(1)

MicroSD card for circuitpython

The Seeed Studio XIAO SAMD21 build-in about 40 KB flash, but it may have not enough space to store the large size python code file, fortunately, Seeed Studio XIAO SAMD21 Expansion board built-in an MicroSD card slot for extending the store space, so you can follow this instruction to learn how to run the circuitpython on the MicroSD card.

note

The MicroSD card system format is FAT or exFAT. If you use other MicroSD card system format that will cause the MicroSD card can not be recognized.

Step 1. Prepare a micro SD Card to plug in the Seeed Studio XIAO SAMD21 expansion board.

Step 2. Assume you do not download the circuitPython file yet, please refer to Installing CircuitPython chapter.

Step 3. Download lib unzips the file, then replace it with the new lib in the CIRCUITPY.

Step 4. Download the main.py file in the CIRCUITPY drive.

The main.py code

import sd
f = open("/sd/hello.txt", "r")   ## read the file from SD card
print(f.read())

Step 5. Download the sd.py file in the CIRCUITPY drive.

The sd.py code

import os
import adafruit_sdcard
import board
import busio
import digitalio
import storage
import sys

# Connect to the card and mount the filesystem for Seeed Studio XIAO .
spi = busio.SPI(board.SCK, board.MOSI, board.MISO)
cs = digitalio.DigitalInOut(board.D2)
sdcard = adafruit_sdcard.SDCard(spi, cs)
vfs = storage.VfsFat(sdcard)
storage.mount(vfs, "/sd")
sys.path.append("/sd")
sys.path.append("/sd/lib")  ## switch to the path to SD card

Buzzer Example

This example for test the buzzer via the run the buzzer.py in the MicroSD card.

Step 1. You can just paste buzzer.py in the MicroSD card.

Step 2. Open main.py in the CIRCUITPY drive.

Step 3. Add import buzzer in the main.py file.

When you finish all the step, the buzzer will work. If you to run other python files in the MicroSD card, please imitate the example.

note

If you want back to Arduino mode, you just need to upload any programme on the Arduino IDE.

Demo

Project 1 - Remote control fan

Overview

This wiki introduce how to make a Mini fan to plase on your room keep cool.

Feature

Automatic swing fan

Component required

Hardware Connection

Please follow the same color line to connect each sensor on the board. Please connect the fan grove cable to D0, servo grove cable to I2C, IR grove cable to D7.

Arduino Instructions

Step 1. Follow the connection picture connect all the sensor on the board.

Step 2. Install the Arduino-IRremote library, this is the guide how to install the library.

Step 4. Copy the code stick on the Aruino IDE then upload it.

Step 5. Place the Fan in the safety position, try to press the button make sure it can work safely.

Code

#include <IRremote.h>
#include <Servo.h>

Servo myservo;  // create servo object to control a servo
int RECV_PIN = 7; // set pin 2 as IR control

IRrecv irrecv(RECV_PIN);

decode_results results;

int pos = 90;    // variable to store the servo position
int fanPin = 0;  // set D6 as control switch
int fanState = LOW;
int IO = 0;

void setup()
{
  Serial.begin(9600);
  Serial.println("Enabling IRin");  // remind enabling IR
  irrecv.enableIRIn(); // Start the receiver
  Serial.println("Enabled IRin");
  myservo.attach(5);  // attaches the servo on pin 2 to the servo object
  pinMode(fanPin, OUTPUT);

}

void loop() {
  if (irrecv.decode(&results)) { //checking IR signal
    if (results.value == 2155829415) {    // Power off/on
      IO++;
      if (IO % 2 == 0) {
        fanState = HIGH;
        digitalWrite(fanPin, fanState);
        delay(100);
      }
      else {
        fanState = LOW;
        digitalWrite(fanPin, fanState);
        delay(100);
      }
    }

    if (results.value == 2155821255 ) {    // fan swing to left
      for (pos; pos <= 89; pos += 1) { // goes from 0 degrees to 90 degrees
        // in steps of 1 degree
        myservo.write(pos);              // tell servo to go to position in variable 'pos'

        delay(40);                       // waits 15ms for the servo to reach the position
        if (irrecv.decode(&results)) {
          irrecv.resume();
          if (results.value == 2155870215)
            break;
        }
      }
    }

    if (results.value == 2155870215 ) {    // fan swing to right
      for (pos; pos >= 1; pos -= 1) { // goes from 90 degrees to 0 degrees
        myservo.write(pos);              // tell servo to go to position in variable 'pos'
        delay(40);                       // waits 15ms for the servo to reach the position

        if (irrecv.decode(&results)) {
          irrecv.resume();
          if (results.value == 2155821255)
            break;
        }
      }
    }
    Serial.println(pos);
    Serial.println(results.value, HEX);
    Serial.println(results.value);
    irrecv.resume();                    //recive next intrustion
  }
  delay(100);
}

Project 2 - Remote control car

Overview

This wiki introduce how to make a remote control car.

Feature

Mini size car easy to across the narrow road

Component required

Hardware Connection

Please follow the same color line to connect each sensor on the board. Please connect the IR sensor grove cable to D0, Mini Motor Driver grove cable to I2C.

Arduino Instructions

Step 1. Follow the connection picture connect all the sensor on the board.

Step 2. Download the Aruidno IDE

Step 3. Install the Arduino-IRremote and Motor driver library, this is the guide how to install the library.

Step 4. Copy the code stick on the Aruino IDE then upload it.

Code

#include <Arduino.h>
#include <U8g2lib.h>
#include <IRremote.h>
#include <SparkFunMiniMoto.h>  // Include the MiniMoto library
// Create two MiniMoto instances, with different address settings.
MiniMoto motor0(0xC4); // A1 = 1, A0 = clear
MiniMoto motor1(0xC0); // A1 = 1, A0 = 1 (default)

#define FAULTn  1     // Pin used for fault detection.

int RECV_PIN = 0; // set pin 2 as IR control
IRrecv irrecv(RECV_PIN);
decode_results results;

void setup() {
  Serial.begin(9600);
  Serial.println("Enabling IRin");  // remind enabling IR
  irrecv.enableIRIn(); // Start the receiver
  pinMode(FAULTn, INPUT);
}

void loop() {
  if (irrecv.decode(&results)) { //checking IR signal
    if (results.value == 2155862055) {
      //Forward  2155862055
      motor0.drive(-600);
      motor1.drive(600);
      delayUntil(20);
    }
    if (results.value == 2155813095) {
      //Brake   2155813095
      motor0.brake();
      motor1.brake();
      delay(100);
    }
    if (results.value == 2155823295) {
      //backward  2155823295
      motor0.drive(600);
      motor1.drive(-600);
      delayUntil(20);
    }
    if (results.value == 2155829415) {
      //Stop  2155829415
      motor0.stop();
      motor1.stop();
      delay(100);
    }
    if (results.value == 2155821255) {
      //turn right   2155821255
      motor0.drive(600);
      motor1.drive(600);
      delayUntil(20);
    }
    if (results.value == 2155837575) {
      //turn left    2155837575
      motor0.drive(-600);
      motor1.drive(-600);
      delayUntil(20);
    }
    irrecv.resume();                    //recive next intrustion

  }
  delay(100);
}

void delayUntil(unsigned long elapsedTime) {
  unsigned long startTime = millis();
  while (startTime + elapsedTime > millis()) {
    if (digitalRead(FAULTn) == LOW) {
      byte result = motor0.getFault();
      result = motor1.getFault();
    }
  }
}

Project 3 - Fingerprint unlocks treasure box -Seeed Studio XIAO

Overview

This box can store your important stuff, and you are not worried about some people will take your thing, the box has the fingerprint function to protecting your thing, and if the fingerprint authorization failed, the buzzer will alarm and the LED ring will display the red colour, only your finger has registered on the board when the begin, then put your finger on the board, when fingerprint pass the authorization, the LED ring will display green colour.

Feature

Easy to record your fingerprint
LED ring can remind you the lock state
The OLED screen can display the current information
The buzzer can remind you the fingerprint whether pass authorization

Component required

Hardware Connection

Please follow the same color line to connect each sensor on the board. Please connect the IR sensor grove cable to D0, Mini Motor Driver grove cable to I2C.

Arduino Instructions

Step 1. Follow the connection picture connect all the sensor on the board.

Step 2. Download the Aruidno IDE

Step 3. Install the u8g2, Servo, Seeed_Arduino_KCT202 and Seeed_LED_Ring library, this is the guide how to install the library.

Step 4. Copy the code stick on the Aruino IDE then upload it.

Demonstration

Record your fingerprint

The screen will display finger recording at the begin, you just need to put your finger on the finger device, after that, the program will analyze your fingerprint, then finish registered.

Identity authorization(pass certification)

The screen will display "Please verify", you need to put your finger on the fingerprint device, then the LED ring will turn to green colour.

Identity authorization(unpass certification)

If other people put their finger on it, the LED ring will turn to red colour and the board will display "Identity deny" meanwhile the alarm will be work.

Code

#include <Servo.h>
#include <Arduino.h>
#include <U8x8lib.h>
#include "ATSerial.h"
#include "Protocol.h"
#include "KCT202.h"
#include "Adafruit_NeoPixel.h"

#define PIXEL_PIN    2    // Digital IO pin connected to the NeoPixels.
#define PIXEL_COUNT 24
#define debug SerialUSB
#define uart  Serial1
FingerPrint_KCT202<Uart, Serial_> kct202;
Adafruit_NeoPixel strip = Adafruit_NeoPixel(PIXEL_COUNT, PIXEL_PIN, NEO_GRB + NEO_KHZ800);

Servo myservo;

Protocol_oprt oprt;
uint8_t err_code = 0;
uint8_t param[10];
uint32_t param_len;
int pos = 0;
const int buttonPin = 1;
int buttonState = 0;
int BuzzerPin = A3;

U8X8_SSD1306_128X64_NONAME_HW_I2C u8x8(/* reset=*/ U8X8_PIN_NONE);

void setup(void) {
  Serial.begin(115200);
  strip.setBrightness(255);
  strip.begin();
  strip.show(); // Initialize all pixels to 'off'
  colorWipe(strip.Color(125, 0, 125), 50);
  u8x8.begin();
  u8x8.setFlipMode(0);
  debug.begin(115200);
  pinMode(buttonPin, INPUT_PULLUP);
  pinMode(BuzzerPin, OUTPUT);
  kct202.begin(uart, debug);
  myservo.attach(0);
  myservo.write(0);
  kct202.autoRegisterFingerPrint(1, 4, LED_OFF_AFTER_GET_GRAGH | PRETREATMENT_GRAGH | NOT_RET_FOR_EVERY_STEP | OVERRIDE_CURR_FINGER_PRINT);

  u8x8.setFont(u8x8_font_chroma48medium8_r);
  u8x8.setCursor(0, 3);
  u8x8.print("finger recording");
  if (0 == kct202.getRegisterResponAndparse()) {
    debug.println("Register ok!");
    u8x8.setFont(u8x8_font_chroma48medium8_r);
    u8x8.setCursor(0, 3);
    u8x8.print("    be ready    ");
    delay(500);
    colorWipe(strip.Color(0, 125, 125), 50);
    u8x8.setCursor(0, 3);
    u8x8.print("   *** 3 ***    ");
    delay(500);
    u8x8.setCursor(0, 3);
    u8x8.print("   *** 2 ***    ");
    delay(500);
    u8x8.setCursor(0, 3);
    u8x8.print("   *** 1 ***    ");
    delay(500);
    u8x8.setCursor(0, 3);
    u8x8.print("   Registered");
    delay(800);
  }
}

void loop(void) {
  uint16_t finger_num = 0;

  kct202.autoVerifyFingerPrint(CHECK_ALL_FINGER_TEMP,
                               LED_OFF_AFTER_GET_GRAGH | PRETREATMENT_GRAGH | NOT_RET_FOR_EVERY_STEP);
  u8x8.setFont(u8x8_font_chroma48medium8_r);
  u8x8.setCursor(0, 3);
  u8x8.print(" Please verify  ");

  if (0 == kct202.getVerifyResponAndparse(finger_num)) {
    debug.println("Verify ok!");
    debug.print("Your finger temp id = ");
    debug.println(finger_num, HEX);
    colorWipe(strip.Color(0, 255, 30), 50);
    u8x8.setFont(u8x8_font_chroma48medium8_r);
    u8x8.setCursor(0, 3);
    u8x8.print("Identity comfirm");
    delay(800);

    analogWrite(BuzzerPin, 128);
    delay(100);
    analogWrite(BuzzerPin, 0);
    delay(100);
    analogWrite(BuzzerPin, 128);
    delay(100);
    analogWrite(BuzzerPin, 0);
    delay(100);

    for (pos = 0; pos <= 90; pos += 1) {
      myservo.write(pos);
      delay(15);
    }
    while (1) {
      //      pinMode(buttonPin, INPUT);
      buttonState = digitalRead(buttonPin);
      u8x8.setFont(u8x8_font_chroma48medium8_r);
      u8x8.setCursor(0, 3);
      u8x8.print("Please close    ");
      Serial.println(pos);
      Serial.println(buttonState);
      if (buttonState == LOW && pos == 91) {
        for (pos = 91; pos >= 0; pos -= 1) { // goes from 180 degrees to 0 degrees
          u8x8.setFont(u8x8_font_chroma48medium8_r);
          u8x8.setCursor(0, 3);
          u8x8.print("Lock closing    ");
          myservo.write(pos);              // tell servo to go to position in variable 'pos'
          delay(15);                       // waits 15ms for the servo to reach the position
        }
        colorWipe(strip.Color(255, 0, 0), 50);
        break;
      }
    }
  }

  else {
    colorWipe(strip.Color(255, 0, 0), 50);
    u8x8.setFont(u8x8_font_chroma48medium8_r);
    u8x8.setCursor(0, 3);
    u8x8.print(" Identity deny ");
    //    myservo.write(0);
    delay(200);

  analogWrite(BuzzerPin, 250);
  delay(2000);
    analogWrite(BuzzerPin, 0);
  delay(100);

    u8x8.setCursor(0, 3);
    u8x8.print("  Please retry  ");
    delay(1500);
  }
}

void colorWipe(uint32_t c, uint8_t wait) {
  for (uint16_t i = 0; i < strip.numPixels(); i++) {
    strip.setPixelColor(i, c);
    strip.show();
    delay(70);
  }
}

Project 4 - Seeed Studio Expansion Base for XIAO - mjolnir

Overview

This hammer is simulated Mjolnir, you need you to record your fingerprint on this device then you will become its master. The hammer needs a magnet to adsorb on the grove - electromagnet until its master to unlock via fingerprint, the hammer can take away.

Component required

Hardware Connection

Please follow the same color line to connect each sensor on the board. Please connect the IR sensor grove cable to D0, Mini Motor Driver grove cable to I2C.

Arduino Instructions

Step 1. Follow the connection picture connect all the sensor on the board.

Step 2. Download the Aruidno IDE

Step 3. Install the u8g2 and Seeed_Arduino_KCT202 library, this is the guide how to install the library.

Step 4. Copy the code stick on the Aruino IDE then upload it.

Code

#include <U8x8lib.h>
#include "ATSerial.h"
#include "Protocol.h"
#include "KCT202.h"

#define debug SerialUSB
#define uart  Serial1
FingerPrint_KCT202<Uart, Serial_> kct202;

Protocol_oprt oprt;
uint8_t err_code = 0;
uint8_t param[10];
uint32_t param_len;

int Electromagnet = 0;

U8X8_SSD1306_128X64_NONAME_HW_I2C u8x8(/* reset=*/ U8X8_PIN_NONE);

// the setup routine runs once when you press reset:
void setup() {
  // initialize the digital pin as an output.

  u8x8.begin();
  u8x8.setFlipMode(0);
  debug.begin(115200);
  pinMode(Electromagnet, OUTPUT);
  digitalWrite(Electromagnet, HIGH);  // turn the Electromagnet on (HIGH is the voltage level)
  kct202.begin(uart, debug);
  kct202.autoRegisterFingerPrint(1, 4, LED_OFF_AFTER_GET_GRAGH | PRETREATMENT_GRAGH | NOT_RET_FOR_EVERY_STEP | OVERRIDE_CURR_FINGER_PRINT);
  u8x8.setFont(u8x8_font_chroma48medium8_r);
  u8x8.setCursor(0, 3);
  u8x8.print("finger recording");
  if (0 == kct202.getRegisterResponAndparse()) {
    u8x8.setFont(u8x8_font_chroma48medium8_r);
    u8x8.setCursor(0, 3);
    u8x8.print("    be ready    ");
    delay(500);
    u8x8.setCursor(0, 3);
    u8x8.print("   *** 3 ***    ");
    delay(500);
    u8x8.setCursor(0, 3);
    u8x8.print("   *** 2 ***    ");
    delay(500);
    u8x8.setCursor(0, 3);
    u8x8.print("   *** 1 ***    ");
    delay(500);
    u8x8.setCursor(0, 3);
    u8x8.print("   Registered");
    delay(800);
  }

}

  // the loop routine runs over and over again forever:
  void loop() {

    uint16_t finger_num = 0;
    kct202.autoVerifyFingerPrint(CHECK_ALL_FINGER_TEMP, LED_OFF_AFTER_GET_GRAGH | PRETREATMENT_GRAGH | NOT_RET_FOR_EVERY_STEP);
    u8x8.setFont(u8x8_font_chroma48medium8_r);
    u8x8.setCursor(0, 3);
    u8x8.print(" Please verify  ");

    if (0 == kct202.getVerifyResponAndparse(finger_num)) {
      u8x8.setFont(u8x8_font_chroma48medium8_r);
      u8x8.setCursor(0, 3);
      u8x8.print("Identity comfirm");
      delay(800);
      digitalWrite(Electromagnet, LOW);  // turn the Electromagnet on (HIGH is the voltage level)
      delay(5000);
      digitalWrite(Electromagnet, HIGH);
    }

    else {
      u8x8.setFont(u8x8_font_chroma48medium8_r);
      u8x8.setCursor(0, 3);
      u8x8.print(" Identity deny ");
      //    myservo.write(0);
      delay(200);

      u8x8.setCursor(0, 3);
      u8x8.print("  Please retry  ");
      delay(1500);
      digitalWrite(Electromagnet, HIGH);  // turn the Electromagnet on (HIGH is the voltage level)

    }
  }

Project 5 - Air Quality Sensor Hub - Seeed Studio Expansion Base for XIAO

Overview

This is an environment detect device to collect PM2.5, PM10, temperature, humidity, CO2 and dust particle via Grove - Laser PM2.5 Sensor, Grove - CO2 & Temperature & Humidity sensor and Grove - dust Sensor respectively.

Component required

Hardware Connection

Please follow the same color line to connect each sensor on the board. Please connect the IR sensor grove cable to D0, Mini Motor Driver grove cable to I2C.

Arduino Instructions

Step 1. Follow the connection picture connect all the sensor on the board.

Step 2. Download the Aruidno IDE

Step 3. Install the u8g2, Seeed_PM2_5_sensor_HM3301 and Seeed_SCD30 library, this is the guide how to install the library.

Step 4. Copy the code stick on the Aruino IDE then upload it.

Code

#include <Arduino.h>
#include <U8x8lib.h>
#include <Seeed_HM330X.h>
#include "SCD30.h"

#define SERIAL_OUTPUT SerialUSB
#define SERIAL SerialUSB

int pin = 7;
unsigned long duration;
unsigned long starttime;
unsigned long sampletime_ms = 5000;//sampe 30s ;
unsigned long lowpulseoccupancy = 0;
float ratio = 0;
float concentration = 0;

const int buttonPin = 1;
int buttonState = 0;
int memu = 0;

U8X8_SSD1306_128X64_NONAME_HW_I2C u8x8(/* reset=*/ U8X8_PIN_NONE);
HM330X sensor;
uint8_t buf[30];

const char* str[] = {"sensor num: ", "PM1.0 concentration(CF=1,Standard particulate matter,unit:ug/m3): ",
                     "PM2.5 concentration(CF=1,Standard particulate matter,unit:ug/m3): ",
                     "PM10 concentration(CF=1,Standard particulate matter,unit:ug/m3): ",
                     "PM1.0 concentration(Atmospheric environment,unit:ug/m3): ",
                     "PM2.5 concentration(Atmospheric environment,unit:ug/m3): ",
                     "PM10 concentration(Atmospheric environment,unit:ug/m3): ",
                    };


///////////////////////////////////////////////////////////////////
//PM2.5 concentration(Atmospheric environment,unit:ug/m3): value
///////////////////////////////////////////////////////////////////
HM330XErrorCode print_result(const char* str, uint16_t value) {
  if (NULL == str) {
    return ERROR_PARAM;
  }
  //  SERIAL_OUTPUT.print(str);
  u8x8.setFont(u8x8_font_chroma48medium8_r);
  u8x8.setCursor(0, 0);
  u8x8.print("PM2.5: ");
  u8x8.setCursor(7, 0);
  u8x8.print(value);
  u8x8.setCursor(11, 0);
  u8x8.print("ug/m");
  Serial.println(value);
  return NO_ERROR;
}

HM330XErrorCode print_result_1(const char* str, uint16_t value) {
  if (NULL == str) {
    return ERROR_PARAM;
  }
  //  SERIAL_OUTPUT.print(str);
  u8x8.setFont(u8x8_font_chroma48medium8_r);
  u8x8.setCursor(0, 0);
  u8x8.print("PM10: ");
  u8x8.setCursor(7, 0);
  u8x8.print(value);
  u8x8.setCursor(11, 0);
  u8x8.print("ug/m");
  Serial.println(value);
  return NO_ERROR;
}

/*parse buf with 29 uint8_t-data*/
HM330XErrorCode parse_result(uint8_t* data) {
  uint16_t value = 0;
  if (NULL == data) {
    return ERROR_PARAM;
  }
  value = (uint16_t) data[6 * 2] << 8 | data[6 * 2 + 1];
  print_result(str[6 - 1], value);
  return NO_ERROR;
}


HM330XErrorCode parse_result2(uint8_t* data) {
  uint16_t value = 0;
  if (NULL == data) {
    return ERROR_PARAM;
  }
  value = (uint16_t) data[7 * 2] << 8 | data[7 * 2 + 1];
  print_result_1(str[7 - 1], value);
  return NO_ERROR;
}

////////////////////////////////////////////////////////////////////

/*30s*/
void setup() {
  Serial.begin(115200);
  Wire.begin();
  u8x8.begin();
  u8x8.setFlipMode(0);
  scd30.initialize();
  pinMode(pin, INPUT);
  pinMode(buttonPin, INPUT_PULLUP);
  starttime = millis();//get the current time;

}

void loop() {
  float result[3] = {0};
  duration = pulseIn(pin, LOW);
  lowpulseoccupancy = lowpulseoccupancy + duration;

  buttonState = digitalRead(buttonPin);

  if (buttonState == LOW) {
    memu++;
    delay(15);
    if (memu == 2) {
      memu = 0;
    }
  }
  Serial.println(memu);

  if (scd30.isAvailable() && memu == 0) {
    scd30.getCarbonDioxideConcentration(result);
    u8x8.setFont(u8x8_font_chroma48medium8_r);
    u8x8.setCursor(0, 3);
    u8x8.print("CO2: ");
    u8x8.setCursor(5, 3);
    u8x8.print(result[0]);
    u8x8.setCursor(12, 3);
    u8x8.print("pmm");
    delay(1000);
  }

  if (sensor.read_sensor_value(buf, 29) && memu == 0) {
    SERIAL_OUTPUT.println("HM330X read result failed!!!");
  }
  if(memu == 0){
  parse_result(buf);
  }

  if ((millis() - starttime) > sampletime_ms  && memu == 0) {
    ratio = lowpulseoccupancy / (sampletime_ms * 10.0); // Integer percentage 0=>100
    concentration = 1.1 * pow(ratio, 3) - 3.8 * pow(ratio, 2) + 520 * ratio + 0.62; // using spec sheet curve

    u8x8.setFont(u8x8_font_chroma48medium8_r);
    u8x8.setCursor(0, 6);
    u8x8.print("Dust: ");

    u8x8.setCursor(6, 6);
    u8x8.print(concentration);

    u8x8.setCursor(12, 6);
    u8x8.print("pcs");

    //    Serial.println(concentration);
    lowpulseoccupancy = 0;
    starttime = millis();
  }



  if (scd30.isAvailable() && memu == 1) {
    scd30.getCarbonDioxideConcentration(result);
    u8x8.setFont(u8x8_font_chroma48medium8_r);
    u8x8.setCursor(0, 3);
    u8x8.print("Temp: ");
    u8x8.setCursor(6, 3);
    u8x8.print(result[1]);
    u8x8.setCursor(10, 3);
    u8x8.print(" C   ");

    u8x8.setCursor(0, 6);
    u8x8.print("Humi: ");
    u8x8.setCursor(5, 6);
    u8x8.print(result[2]);
    u8x8.setCursor(8, 6);
    u8x8.print("  %     ");

    delay(1000);
  }

  if (sensor.read_sensor_value(buf, 29) && memu == 1) {
    SERIAL_OUTPUT.println("HM330X read result failed!!!");
  }
  if(memu == 1){
  parse_result2(buf);
  }
}

Project 6 - Seeed Studio Expansion Base for XIAO - Heart Rate

Overview

This simple and inexpensive project is based on the Seeed Studio Expansion Base for XIAO to report the heart rate. The device used has an I2C two-wire interface and therefore keeps the wiring down to a minimum.

Component required

Hardware Connection

Please follow the same color line to connect each sensor on the board. Please connect the IR sensor grove cable to D0, Mini Motor Driver grove cable to I2C.

Arduino Instructions

Step 1. Follow the connection picture connect all the sensor on the board.

Step 2. Download the Aruidno IDE

Step 3. Install the u8g2 library, this is the guide how to install the library.

Step 4. Copy the code stick on the Aruino IDE then upload it.

Code

#include <Arduino.h>
#include <U8x8lib.h>

#include <Wire.h>

U8X8_SSD1306_128X64_NONAME_HW_I2C u8x8(/* reset=*/ U8X8_PIN_NONE);

void setup() {
  Serial.begin(9600);
  Serial.println("heart rate sensor:");

  u8x8.begin();
  u8x8.setFlipMode(1);
  Wire.begin();
}
void loop() {
  Wire.requestFrom(0xA0 >> 1, 1);    // request 1 bytes from slave device
  while (Wire.available()) {         // slave may send less than requested
    unsigned char c = Wire.read();   // receive heart rate value (a byte)
    u8x8.setFont(u8x8_font_chroma48medium8_r);
//    u8x8.setCursor(0, 3);
//    u8x8.print("blood detecting ");
//    delay(10000);

    u8x8.setCursor(0, 3);
    u8x8.print("HeartRate: ");
    u8x8.setCursor(10, 3);
    u8x8.print(c);
    u8x8.setCursor(13, 3);
    u8x8.print("bpm");
    Serial.println(c);

  }
  delay(500);
}

Resources

[PDF]ETA1038
[PDF]ETA3410
[PDF]ETA6003
[PDF]PCF8563T
[PDF]Seeed Studio Expansion Base for XIAO_v1.0_SCH_200824
[SCH]Seeed Studio Expansion Base for XIAO_v1.0_200824
[BRD]Seeed Studio Expansion Base for XIAO_v1.0_200824

Tech Support

Please do not hesitate to submit the issue into our forum.

Features​

Specification​

Applications​

Part List​

Getting Started​

Materials Required​

Hardware Overview​

Pinout Diagram​

Expansion Board Usage​

Connection​

Battery usage​

Modules on the expansion board​

OLED Display​

LED control by User Button​

Buzzer​

Play Song with Passive Buzzer​

Servo Control by Rotary Angle Sensor​

RTC clock display​

Acrylic Case for Seeed Studio Seeed Studio Expansion Base for XIAO​

Circuitpython on Seeed Studio XIAO SAMD21 with expansion board​

Installing CircuitPython​

CircuitPyhton Blink example​

MicroSD card for circuitpython​

Demo​

Project 1 - Remote control fan​

Project 2 - Remote control car​

Project 3 - Fingerprint unlocks treasure box -Seeed Studio XIAO​

Project 4 - Seeed Studio Expansion Base for XIAO - mjolnir​

Project 5 - Air Quality Sensor Hub - Seeed Studio Expansion Base for XIAO​

Project 6 - Seeed Studio Expansion Base for XIAO - Heart Rate​

Resources​

Tech Support​

Features

Specification

Applications

Part List

Getting Started

Materials Required

Hardware Overview

Pinout Diagram

Expansion Board Usage

Connection

Battery usage

Modules on the expansion board

OLED Display

LED control by User Button

Buzzer

Play Song with Passive Buzzer

Servo Control by Rotary Angle Sensor

RTC clock display

Acrylic Case for Seeed Studio Seeed Studio Expansion Base for XIAO

Circuitpython on Seeed Studio XIAO SAMD21 with expansion board

Installing CircuitPython

CircuitPyhton Blink example

MicroSD card for circuitpython

Demo

Project 1 - Remote control fan

Project 2 - Remote control car

Project 3 - Fingerprint unlocks treasure box -Seeed Studio XIAO

Project 4 - Seeed Studio Expansion Base for XIAO - mjolnir

Project 5 - Air Quality Sensor Hub - Seeed Studio Expansion Base for XIAO

Project 6 - Seeed Studio Expansion Base for XIAO - Heart Rate

Resources

Tech Support