W600 Module

The W600 Module is a cost-effective 2.4GHz WiFi module support 802.11b/g/n. Seeed W600 Module is based on the W600 chip which features ARM Cortex-M3 with 1MB on-chip flash and freeRTOS kernel.

We take the pins of the W600 chip out and put them on the back of the board, including I2S/I2C/SPI/GPIO/PWM/UART/SDIO. In addition, this module has an on-board PCB Antenna, no need to design the antenna separately, so you can quickly deploy the module to your own board. We also have made CE/FCC certification for this module and you can use it directly for business projects.

Features

• Integrated 32bit Embedded Cortex-M3 CPU, operating frequency 80MHz

• Integrated 288KB RAM

• Integrated 1MB FLASH

Interface

• Integrated GPIO device controller

• Integrated 2 UART interface, support RTS/CTS, baud rate: 1200bps~2Mbps

• Integrated one high speed SPI controller, operating frequency: 0~50MHz;

Wireless

• Support IEEE802.11 b/g/e/i/d/k/r/s/w/n

• Support 2.4~2.4835 GHz

• Support Wi-Fi WMM/WMM-PS/WPA/WPA2/WPS

• Support Wi-Fi Direct

• STBC、GreenField、Short-GI

• Support multiple network protocols: TCP/UDP/ICMP/DHCP/DNS/HTTP

Others

• Supports AT+ instruction protocol based on ASCII encoding (UART interface)

• Support for user‐programmable GPIO control

• On-board Antenna

Specification

Category	Item	Parameter
Wireless	Support Wi‐Fi Mode	IEEE802.11b/g/n
	RF system impedance	50Ω
	Frequency Range	2.4~2.4835 GHz
	Receiving sensitivity	20MHz MCS7@‐71dBm; 40MHz MCS7@‐68dBm; 54Mbps@‐73dBm; 11Mbps@‐86dBm; 1Mbps@‐95dBm;
	Physical layer data rate	802.11n MCS 0~7 150Mbps
	Modulation	DSSS、OFDM、DBPSK、DQPSK、CCK、QAM16/64
	Output Power	IEEE802.11b, DSSS 1Mbps, POUT = +17dBm; IEEE802.11g, OFDM 54Mbps, POUT = +10dBm; IEEE802.11n, OFDM MCS7, POUT = +10dBm
Hardware	Interface Type	UART/SPI/GPIO
	Interface rate	2Mbps@UART (Max) 50Mbps@SPI (Max)
	Operating Voltage	3.3V(Module)/5V(Development Board)
	Operating humidity	5%~90% (No condensation)
	storage temperature	‐40~+125 ℃
	Operating temperature	‐40~+85℃
Software	Network Type	STA/AP/AP+STA/Wi‐Fi Direct
	Verification	WEP/WPA‐PSK/WPA2‐PSK
	Encryption	WEP64/WEP128/TKIP/CCMP(AES)
	WPS Function	WPS
	Energy saving	PS‐POLL/Standby
	Network protocol	TCP/UDP/ARP/ICMP/DHCP/DNS/HTTP
	Interface Protocol	AT+ instruction set

note

For more detail about specifications, please check the W600 Specification V1.0.0_EN.pdf and W600 HardwareDesignGuide_v1.0.1.pdf

Typical Applications

intelligent home appliances
smart home
wireless audio and video
smart toys
medical monitoring
industrial control
other Internet of Things applications

Hardware Overview

Block Diagram

Pinout

Getting Started

To use the W600 Module, you need to use USB-to-Serial Tools to connect the RX/TX pins to your computer, also you need to power this module with the 3.3v and GND pins.

note

For mac, we found that some version of mac system can not recognize the on-board USB-to-Serial chip CH330N, please check here for solution Mac os driver issue

We use the serial port tool sscom to send the AT command. You can use your favorite serial port tool, in case you want to use sscom, you can download it Here.

What ever, please make sure you have checked the option AddCrLf, and set the baud rate to 115200

Tap AT+ then click SEND or press ++enter++ key to to check if the connection was successfully established.

AT+

When it returns +OK, you can use the AT command to control this module.

Create a SoftAP process

1- WPRT sets the wireless network card working mode to SoftAP:

AT+WPRT=2

2- APSSID Set the AP SSID for the STA, e.g.MyAP:

AT+APSSID=MyAp

3- APENCRY Set the wireless network card security mode to WEP64:

AT+APENCRY=1

Parameter：

open：0，WEP64：1，WEP128：2

4- APKEY Set the wireless network card key to 12345

AT+APKEY=1,1,12345

Parameter 1：Key format， 0 means HEX, 1 means ASCII

Parameter 2：index: Key index number, 1 to 4 are used for WEP encryption keys, and other encryption methods are fixed to 0.

Parameter 3：wireless key, e.g.：12345

5- APNIP Set the ip address and subnet mask

AT+APNIP=1,192.168.1.1,255.255.255.0,192.168.1.1,192.168.1.1

Parameter 1：address type: 0 means dynamic allocation using DHCP, 1 means static address
parameter 2：ip:192.168.1.1
parameter 3：netmask：255.255.255.0
parameter 4：gateway：192.168.1.1
parameter 5：dns：192.168.1.1

6- PMTF saves the above parameters to spi flash, just start from step 7 with the next boot.

AT+PMTF

7- WJOIN Create wireless network MyAp

AT+WJOIN

8- SLIST Query the STA information which connected to your SoftAP.

AT+SLIST

Scan AP Process

Wireless network card scanning AP's AT command is ：

AT+WSCAN

The last paremeter is the signal strength, unit db

STA joins the AP process

1- WPRT Set the working mode to STA

AT+WPRT=0

2- SSID Set the AP name to join. e.g. TEST_AP

AT+SSID=TEST_AP

3- KEY Set the wireless key of the AP you want to join. e.g. 12345678

AT+KEY=1,0,12345678

parameter 1：0 means HEX, 1 means ASCII

parameter 2：index: The key index number, 1 to 4 is used for the WEP encryption key. The other encryption methods are fixed to 0.

parameter 3： Wireless key e.g.：12345678

4- NIP Enable DHCP

AT+NIP=0

5- PMTF Save the above parameters to spi flash, Just start from step 6 with the next boot

AT+PMTF

6- WJOIN Join the wireless network TEST_AP

AT+WJOIN

Create an APSTA process

1- WPRT Set the working mode to APSTA

AT+WPRT=3

2- SSID Set the AP name to be joined, such as TEST_AP

AT+SSID=TEST_AP

3- KEY Set the wireless key of the AP you want to join. e.g. 12345678

AT+KEY=1,0,12345678

parameter 1：0 means HEX, 1 means ASCII

parameter 2：index: The key index number, 1 to 4 is used for the WEP encryption key. The other encryption methods are fixed to 0.

parameter 3： Wireless key e.g.：12345678

4- APSSID Set the network name of the created SOFTAP

AT+APSSID=”MYSoftAP”

5- APENCRY Set the encryption type of SoftAP (such as WPA2-TKIP)

AT+APENCRY=5

6- APKEY Set the password for SoftAP (e.g. ASCII code 87654321)

AT+APKEY=1,0,87654321

7- APNIP Set the IP address and subnet mask

AT+APNIP=1,192.168.1.1,255.255.255.0,192.168.1.1,192.168.1.1

8- PMTF Save the above parameters to spi flash, just start from step 9

AT+PMTF

9- WJOIN Join the wireless network TEST_AP

AT+WJOIN

note

For more detail about AT command, please check the WM_W60X_SDK_AT Command_V1.0.2.pdf

Firmware Programming

For the firmware programming please check here：

WM_W60X_SDK_User Manual_V1.0.0.pdf and WM_W60X_Firmware Generation Guide_V1.1.pdf

FAQ

Q1.How the STA disconnects the AP

A: The wireless network card disconnects the AP's AT command:

AT+WLEAV

Q2.SoftAP disconnected

A: The AT command of SoftAP disconnected network is:

AT+WLEAV=2

Q3.How STA view current status

A: The AT command for the wireless network card to view the status of the current network card is:

AT+LKSTT

Q4. How to View current SoftAP status

A: The AT command to view the current SoftAP status is:

AT+APLKSTT

Schematic Online Viewer

Resouce

[PDF] WM_W60X_SDK_AT Command_V1.0.2.pdf
[PDF] W600 HardwareDesignGuide_v1.0.1.pdf
[PDF] W60X_SDK_User Manual_V1.0.0.pdf
[PDF] WM_W60X_Firmware Generation Guide_V1.1.pdf
[ZIP] W600 Module schematic files
[ZIP] sscom

Tech Support

Please do not hesitate to submit the issue into our forum

Features​

Specification​

Typical Applications​

Hardware Overview​

Block Diagram​

Pinout​

Getting Started​

Create a SoftAP process​

Scan AP Process​

STA joins the AP process​

Create an APSTA process​

Firmware Programming​

FAQ​

Schematic Online Viewer​

Resouce​

Tech Support​

Features

Specification

Typical Applications

Hardware Overview

Block Diagram

Pinout

Getting Started

Create a SoftAP process

Scan AP Process

STA joins the AP process

Create an APSTA process

Firmware Programming

FAQ

Schematic Online Viewer

Resouce

Tech Support