Skip to main content

Seeeduino Crypto (ATmega4809 ECC608)

enter image description here

Seeeduino Crypto is made for encryption. It is based on the high performance ATmega4809 and microchip ECC608 encryption chip.With the help of ECC608 encryption chip, you can experience I2C encryption and other encrypted communication.

In addition to encryption, Seeeduino Crypto has the same functions as Seeeduino V4.2 / Arduino Uno Rev3. It has rich interface resources, including 6 analog input pins, 14 digital I/ o-5s for PWM output, with 2 Grove I2C ports and 1 Grove UART port. Just plug it in and use hundreds of sensors and actuators.

The control solution Seeeduino Crypto is the same as ARDUINO UNO WIFI REV2. The difference is that Seeeduino Crypto does not have onboard WIFI. You can add an Arduino wifi module if necessary. Correspondingly, the price of Seeeduino Crypto is less than half of ARDUINO UNO WIFI REV2.

tip
This product allows users to experience the encryption mode of I2C communication with great plasticity.

enter image description here

Features

  • High-performance ATmega4809 microcontroller

  • High-securitycryptographic Chip ECC608, supports SHA-256 & HMAC Hash / AES-128

  • 2 Grove I2C + 1 Grove UART, easy to prototype

  • Type C power supply + data transmit

Specification

ItemDetail
ChipMicrocontroller: ATMEGA4809-AFR / Encryption: ECC608
Clock Speed16Mhz
I/O ResourceAnalog Input Channels: 6 /Digital I/O Pins: 14 / PWM Channels: 5
Peripheral Interface2 Grove I2C Port / 1 Grove UART Port / 1 ICSP Interface /1 USB Type C data port
Operating Voltage5V
Power Supply5V USB Type C / 8 -15 V DC Jack Input

Hardware Overview

enter image description here

  • Type C It is the board Type C interface, connected to the PC end, used as power supply and download.

  • LED RX / LED TX Serial communication indicator LEDS TX,RX, Convenient for users to know the receiving and receiving status of serial communication.

  • DC Power Jack The input voltage is 8v-15v.

  • Reset Button and Reset LED Used to reset the board, when reset, the reset lamp will flicker.

  • Power LED The system power indicator.

  • ATMEGA32U4-MU Chip The chip used as a USB to UPDI download is connected to the master MCU atmega4809-afr to burn the program to the master MCU.

  • ATECC608 Encryption Chip An encryption chip for I2C communication.

  • ATMEGA4809-AFR Chip Onboard MCU, as the main control chip of the system.

  • Grove Connectors Contains two I2C and a UART standard Grove interface

note
When using serial port to communicate the output data, there should be a certain delay of more than 25ms, otherwise the serial port may be stuck.

Getting Started

note
This part is based on Arduino 1.8.10 under Windows 10.

First of all, you need to Install an Arduino Software.

enter image description here

Launch the Arduino application

Double-click the Arduino application (arduino.exe) you have previously downloaded.

note
If the Arduino Software loads in a different language, you can change it in the preferences dialog. See the [Arduino Software (IDE) page](https://www.arduino.cc/en/Guide/Environment#languages) for details.

Open the Blink example

Open the LED blink example sketch: File > Examples >01.Basics > Blink.

enter image description here

Add Seeeduino to your Arduino IDE

Click on Tools > Board > Boards Manager, you can tap the keyword 'MegaAVR' at the search bar , find Arduino MegaAVR, and Install it.

enter image description here

Select your board

You'll need to select the entry in the Tools > Board menu that corresponds to your Arduino. Selecting a Arduino Uon WIFI Rev2.

enter image description here

Select your serial port

Select the serial device of the Arduino board from the Tools | Serial Port menu. This is likely to be COM3 or higher (COM1 and COM2 are usually reserved for hardware serial ports). To find out, you can disconnect your Arduino board and re-open the menu; the entry that disappears should be the Arduino board. Reconnect the board and select that serial port.

enter image description here

Upload the program

Now, simply click the "Upload" button in the environment. Wait a few seconds and if the upload is successful, the message "Done uploading." will appear in the status bar.

enter image description here

A few seconds after the upload finishes, you should see the pin 13 (L) LED on the board start to blink (in orange). If it does, congratulations! You've gotten Arduino up-and-running. If you have problems, please see the troubleshooting suggestions.

Resources

Tech Support

Please submit any technical issue into our [forum](https://forum.seeedstudio.com/).

Loading Comments...